COMMON SPARE PARTS LIST FOR ALL MACHINES
**ALWAYS HAVE THE MODEL AND SERIAL NUMBER OF MACHINE WHEN LOOKING FOR PARTS**
If the information you are seeking is not contained in one of these pages, please use one of the "Click here for available manuals at challengemachinery.com" hyperlinks below to access our online manuals page and choose the Product type, Model and Serial Number of your machine for a specific manual which will contain more comprehensive parts listings and illustrations.
CLICK HERE FOR DETAILS OF OUR DEALER SPARE PARTS KIT
MODEL	PAGE
PAPER CUTTERS
SPARTAN 150 M		2
SPARTAN 150 A / SA		3
SPARTAN 185 A / AEP / SA		4
TITAN 200 M		5
TITAN 200 BC		6
TITAN 200 STANDARD & TC		7
TITAN 230 STANDARD & TC		8
TITAN 265 STANDARD & TC		9
CHAMPION 305 X SERIES & TC		10
CHAMPION 370 X SERIES & TC		11
DAEHO		12
PAPER TRIMMERS
CMT-130		13
CMT-330		14
SINGLE CORNERING MACHINES
SCM		15
DRILLS
HANDY-DRILL		16
JF		16
EH-3C		17
EH-3D		18
MS-5		19
MS-10A		20
MS-10B		21
DRILL SHARPENERS		22
DRILL BITS		22
JOGGERS
HANDY JOG		23
COMBINATION (HDJ) "A" JOGGER		23
I-JOG		23
PADDERS/LIFTING/HANDLING
HANDY-PADDER		24
PADDY-WAGON		24
HANDY-CART		24
PAK-RAK II		24
FOLDERS
820/870 MEDALIST		25
Dealer Spare Parts Kit    K-12426		All items below are contained in this kit
Cutting Care Kit	16077	Contains 16oz of silicon, 16oz of Rust B gone and 1 qt of wax  (Quantity of 1)
Cut Sticks	4166	20" Cut Stick  (Quantity of 12)
	4171	30.5" Cut Stick  (Quantity of 12)
Drill Ease Stick	4688	(Quantity of 48)
Book Guide Assembly	5-7-M361	(Quantity of 2)
Pressure Gauge	8P-629-3	Gauge used on hydraulic manifolds  (Quantity of 2)
1 & 1/2" Wood Blocks	A-4682	Pkg. of 12  (Quantity of 2 Pkg.'s)  For JF Drill
Drill Sharp/Chip Remover	A-4950-2	(Quantity of 2)
1/4 Drill Bit	CD-4	2" Drill capacity  (Quantity of 6)
1/4 Drill Bit	CD-4-2-1/2	2 & 1/2" Drill capacity  (Quantity of 6)
5/16 Drill Bit	CD-5	2" Drill capacity  (Quantity of 6)
5/16 Drill Bit	CD-5-2-1/2	2 & 1/2" Drill capacity  (Quantity of 6)
3/8 Drill Bit	CD-6-2-1/2	2 & 1/2" Drill capacity  (Quantity of 6)
3" Wood Blocks	KK-473-3	Pkg. of 12  (Quantity of 2 Pkg.'s)  For EH-3 Drill
Flat Belt	S-1661-1	Belt for EH-3 drills
SPARTAN Series
150 M	CMC-150M	Weight 80 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife � Standard H.S.S.	60011-2
Knife Dimensions	Measures  18-� � x 1-5/8� x � �	Minimum Height 1-��
Cutting Stick	60057	(Pkg. of 12)  Measures 16" x 1/2" x 1/2"
Cut Stick Hook	5064	For removing the Cut Stick
Jogging Aid	60058
Knife Lifter Assembly	60061
Knife Bolts	H-6910-403	6 required
Knife Bolt Wrench	W-189	5/32� Hex �T� Allen Wrench
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Cut Button	E-3129	1 N.O. Contact
Display Board	EE-3065
Encoder	E-2467-2
Encoder Cable	EE-2899-2
Jack Assembly	EE-3077
Line Light Board	EE-3126
Wall Transformer	E-3078
MECHANICAL
Back Gauge Assembly	60203
Back Gauge Floating Fingers	60204	8 per machine, plastic
Back Gauge Nut (Housing)	61045-1	Also order (1) 60214 (Lead screw Nut)
Belt	61063
Clamp	61025
Clamp Hand wheel	61033
Clamp Lead Screw	61026	Also order 2 each 20075-10 (M & SA Models)
Clamp Nut	61066
Encoder Pulley	60208
Back Gauge Hand crank	60043
Guide Shaft	61044
Hood (Formed Plastic)	61052
Hood Torsion Spring	61075
Knife Bar Link	61020
Knife Latch Replacement Kit	K-61074
Knife Latch Torsion Spring	61071
Lead Screw	61047
Lead Screw Nut	60214	Also order (1) 61045-1  (Nut Housing)
Tilt Shield Stiffener	61060
Accessories
Stand	61070
150 A / SA	CMC-150	Weight 170 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife � Standard H.S.S.	60011-1
Knife Dimensions	Measures  18-� � x 1-5/8� x � �	Minimum Height 1-��
Cutting Stick	60057	(Pkg. of 12) Measures 16" x 1/2" x 1/2"
Cut Stick Hook	5064	For removing the Cut Stick
Jogging Aid	60058
Knife Lifter Assembly	60061
Knife Bolts	H-6910-403	6 required
Knife Washers	8815-1	6 required
Knife Bolt Wrench	W-189	5/32� Hex �T� Allen Wrench
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Brake Replacement Kit	K-3455
Circuit Breaker	E-3074	8 Amps
Cut Buttons (Round)	E-3129	1 N.O. Contact
Display Board	EE-3065	EPROM Not Included, See P/N EE-1888-()
Encoder	E-2467-2
Encoder Cable	EE-2899
Hood Magnet Coil Assembly	EE-3111
Hood Switch	E-866-9
Knife Limit Switches	E-3112	For either UP or DOWN
Line Light Board	EE-3081
Motor & Brake Assembly	E-1600-197
Motor & Gearbox Assembly	K-60005
Power Cord � 120V	EE-3188
Preset Micro Switch	E-866-4
Relay PC Board	EE-3061-1
Transformer (120v)	EE-3115
MECHANICAL
Back Gauge Assembly	60203
Back Gauge Floating Fingers	60204	8 per machine, plastic
Back Gauge Nut (Housing)	60202-1	Also order (1) 60214 (Lead Screw Nut)
Belt � MXL	60211
Clamp	61025
Clamp Hand Wheel	60093
Clamp Lead Screw	61026	Also order 2 each 20075-10 (M & SA Models)
Clamp Nut	61066
Front Crank Handle	60043
Gib Insert (051260 and down)	56256
Gib Insert (051261 and up)	60074
Guide Shaft	61044
Handle � Tilt Shield	60047
Lead Screw	60210
Lead Screw Nut	60214	Also order (1) 60202-1 (Nut Housing)
Pull-Down Link	60010
Tilt Shield (Formed Plastic)	60035
Accessories
Stand	60065
185 A, SA, AEP	CMC-185	Weight 650 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife � Standard H.S.S.	63017-1
Knife Dimensions	Measure 22-� � x 2-5/8� x 3/8�	Minimum Height 2-3/8�
Book Guides	5-7-M361	2 required
Cutting Stick	63015	(Pkg. of 12) Measures 18-� � x � � x � "
Cut Stick Hook	5064	For removing the Cut Stick
Jogging Aid	A-12608-2	2-7/8" High
Knife Bolts	H-6910-505	6 required
Knife Bolt Wrench	W-191	3/16� Hex �T� Allen Wrench
Knife Lifter Assembly	63073
Machine Lifter Handles (4)	H-6913-1048
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Back Gauge Motor	E-1600-167 (120V Option)	For 230V Option call Challenge Machinery
Cir. Breaker w/On-Off Switch	E-3074-6  (120V Option/30Amp)	E-3074-1 (230V Option/15Amp)
Clamp Down Button	E-3073-1	2 N.O. Contacts       A, AEP
Clamp Up Button / Right Cut	E-3073-3	1 N.O. & 1 N.C. Contacts
Clamp Up Limit Switch	E-3112	A, AEP
Clamp Motor	E-1600-39	Consult manual for specific machine
	E-1600-40	Consult manual for specific machine
	E-1600-41	Consult manual for specific machine
	E-1600-42	Consult manual for specific machine
Cut Motor	E-1600-XXX	Consult manual for specific machine
Display Assembly  A	EE-3158	EPROM Not Included, See P/N EE-1888-()
Display Assembly  AEP	EE-3157	EPROM Not Included, See P/N EE-1888-()
Display Assembly  SA	EE-3164	EPROM Not Included, See P/N EE-1888-()
Encoder	E-2467
Encoder Cable	EE-2534-3
Gearbox Assembly Only	63002-GB
Hood Coil	EE-3111
Hood Switches	E-866-9	Two per machine
Knife Down Limit Switch	E-3112-1
Knife Up Limit Switch	E-3112-2
Left Cut / Clamp Down Button	E-3073	1 N.O. Contact
Line Light PC Board	EE-3162
Main Board	EE-3132-1	120v
Main Board	EE-3165	230v
Motor, Brake & Gearbox Assy.	63002
Power Cord (120V 60Hz)	EE-3163
Preset Proximity Switch	E-2204-1	AEP
MECHANICAL
Back Gauge	63204	Does not include fingers and dowel pin
Back Gage Dowel Pin	H-5246-406
Back Gage Floating Fingers	60204	10 required
Clamp	63019
Clamp Hand Wheel	63045	SA
Clamp Lead Screw	63023	SA
	63075	A, AEP
Clamp Nut	63029-2
Front Hand Wheel B/G	63047	SA, A, 4" Diameter
Handle � Tilt Shield	60047
Knife Bar Replacement Kit	K-63016-1
Lead Screw Nut - Manual	63216	SA, A
Lead Screw Nut � Power	63206	AEP
Tilt Shield (Formed Plastic)	63040
TITAN Series
200 M		Weight 800 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife Blade	A-10034-1
Knife Dimensions	Measures 23-�� x 3� x 3/8�	Minimum Height 2-5/8�
Book Guides	5-7-M361	2 required
Cutting Stick	4166	(Pkg. of 12) Measures 20" x �� x ��
Cut Stick Hook	5064	For removing the Cut Stick
False Clamp Plate	AA-10061	Mounting wing nuts included
Jogging Aid	A-12608-2	2-7/8" High
Knife Bolts	H-6918-608	4 required
Knife Bolt Washers	8815	4 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	43108
Line/Cut Light Bulbs	E-967-1	12v automotive, #1156
Magnetic Clamping Pad	50082	2 each 3� x 15�
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Auxiliary Contact	E-2376-8	S/N: 09609 & Above  N.O. / N.C.
Cut Button � Recessed	E-3073-3	S/N: 05283 & Below, N.O. / N.C.
Cut Button � Mushroom	E-3127-3	S/N: 05284 & Above, N.O. / N.C.
Cut Solenoid	E-1069-19	24 VDC
Display Board	EE-1675-1
Encoder	E-2467-1
Encoder Coupling	47053	1� Long rubber tubing
Knife Latch Assembly	41120-4
Power Switch	K-3085	For machines 2010 & Older
		For machines 2011 & Newer
Preset Board	EE-1688-1
Relay Board	EE-2897-2
Safety Eyes	K-3453	S/N: 103478 & Below
	E-3370	S/N: 103479 & Above    *For repairs only & E-3336 Controller can be sold separately*
Starter-Motor Relay	K-3325	S/N: 09608 & Below
	E-2805-6	S/N: 09609 & Above
MECHANICAL
Back Gauge Nut	8826	S/N: 09609 & Below
	8826-1	S/N: 09610 & Above
Clamp Pull Down Rods	10075-1	2 per machine
Cut Stick Stop Repair	K-43058-2	Repair broken screw/stop
Knife Latch	41120-4
Lead Screw	K-43505	S/N: 09609 & Below
	10037-2	S/N: 09610 & Above
Left Side Guide	43058-1	Repair broken cut stick stop
HYDRAULIC
Clamp Cylinder	H-211-3 & (2) H-230-3 Fittings	See notes in MAX
	H-211-3 Only	See notes in MAX
Clamp Press. Valve	H-203-13
Clamp Up Seq. Valve	H-203-6
Cut Valve	H-200-2
Hydraulic Fluid	S-1991-4 (5 gal)      ISO VG 100 Weight	1 gallon tank capacity
Hyd Power Unit	H-220-6	120VAC/60Hz
Hyd Power Unit	H-220-5	240VAC/60Hz
Hyd Power Unit	H-220-7	240VAC/50Hz
Knife Cylinder	K-10018-1
	H-210-4 & (2) H-230-3 Fittings
	H-210-4 Only
Knife Seq. Valve	H-203-17
Manifold O-rings	S-1810-10	3/4� O.D.
Manifold O-rings	S-1810-15	7/8� O.D.
Oil Replacement Kit	K-43093
Oil Tank Seal	S-1810-37	"O" ring,
Pressure Gauge	8P-629-3	Clear oil filled
200BC	CMC-200-BC	Weight 800 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife Blade	A-10034-1
Knife Dimensions	Measures 23-�� x 3� x 3/8�	Minimum Height 2-5/8�
Book Guides	5-7-M361	Each, 2 required
Cutting Stick	4166	(Pkg. of 12) Measures 20" x �� x ��
Cut Stick Hook	5064	For removing the Cut Stick
False Clamp Plate	AA-10061	Mounting wing nuts included
Jogging Aid	A-12608-2	2-7/8" High
Knife Bolt Wrench	W-164
Knife Lifter Assembly	43108
Knife Bolts	H-6918-608	4 required
Knife Bolt Washers	8815	4 required
Line/Cut Light Bulbs	E-967-1	12v automotive, #1156
Magnetic Clamping Pad	50082	Pkg. of 2 each 3� x 15�
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Cut Buttons	E-3073-3	2 per machine, n.o./n.nc
Cut Solenoid	E1069-19
Display Board	EE-3418
Encoder	E-2467-2
Encoder Coupling	47053	1� long rubber tubing
Knife Change Switch	E-1140-19
Knife Latch Assembly	41120-4
Preset Board	EE-1688-1
Power Switch	E-1140-8
Relay Board	EE-2897-2
Safety Eyes	E-3370	*For repairs only & E-3336 Controller can be sold separately*
	K-3412	Converts tilt shield to electric eyes  (Comes with K-3431 Cut Button upgrade kit which can only be used with electric eyes upgrade kit)
Tilt Shield Switch	E-866-9
MECHANICAL
Back Gauge Nut	8826-1	Plastic
Clamp Pull Down Rods	10075-1	2 per machine
Cut Stick Stop Repair	K-43058-2	Repair broken screw/stop
Knife Latch	41120-4
Left Side Guide	43058-1	Repair broken cut stick stop
HYDRAULIC
Clamp Cylinder	H-211-3 & (2) H-230-3 Fittings	Consult ChallengeTech Support
	H-211-3 Only	Consult ChallengeTech Support
Clamp Press. Valve	H-203-13
Clamp Up Seq. Valve	H-203-6
Cut Valve	H-200-2
Hydraulic Fluid	S-1991-4 (5 gal)      ISO VG 100 Weight	1 gallon tank capacity
Knife Cylinder	H-210-4 & (2) H-230-3 Fittings	See notes in MAX
	H-210-4 Only	See notes in MAX
Knife Seq. Valve	H-203-17+B303
Manifold O-rings	S-1810-10	3/4� O.D.
Manifold O-rings	S-1810-15	7/8� O.D.
Oil Replacement Kit	K-43093
Oil Tank Seal	S-1810-37	"O" ring,
200 Standard & TC	CMC-200	Weight 800 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife Blade	A-10034-1
Knife Dimensions	Measures 23-�� x 3� x 3/8�	Minimum Height 2-5/8�
Book Guides	5-7-M361	2 required
Cutting Stick	4166	(Pkg. of 12) Measures 20" x �� x ��
Cut Stick Hook	5064	For removing the Cut Stick
False Clamp Plate	AA-10061	Mounting wing nuts included
Jogging Aid	A-12608-2	2-7/8" High
Knife Bolts	H-6918-608	4 required
Knife Bolt Washers	8815	4 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	43108
Line/Cut Light Bulbs	E-967-1	12v automotive, #1156
Magnetic Clamping Pad	50082	2 each 3� x 15�
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
Cut Button Kit	K-2874	S/N: 981342 & Below, For 1 button replacement
Cut Buttons (Green)	E-3073-6	Non-Mushroom cap style, 3 N.O. contacts
Cut Buttons	E-3127-4	Mushroom cap style, 3 N.O. contacts
Cut Solenoid	E-1069-17	24VAC
Display Assembly	EE-2758-4	S/N: 083331 & Below
PCB Backer Asm	EE-3439-1	White back ground
Encoder	E-2467
Encoder coupling	47053	1� long rubber tubing
Interlock Switches	E-2457-6	2 Required & Order qty. (6) E-1214-65
Keyboard Interface board	EE-2764-1	S/N: 083331 & Below
Knife Latch Assembly	41120-4
LED Line Light Assembly	EE-3081-1	S/N: 083319 and up
Main Board	EE-2807-2	EPROM not included
Panel - Control Console	43102	Front panel keypad
Preset Board	EE-1688-1
Proximity Switch	E-2204-1	Universal, must cut wire to required length
Safety Eyes	K-3337	S/N: 03245 to 08330, upgrade from tilt shield
	K-3337-1	S/N: 08331 & up, upgrade from tilt shield
	E-3370	S/N: 103479 and up and upgraded tilt shields, *For repairs only & E-3336 Controller can be sold separately*
TC Electronics
Display Board	EE-3400-1-C	Board behind LCD panel
�CAN� Cable	EE-3460-1	Interface cable between display/motor boards
Hand Wheel Potentiometer	EE-3213	With soldered cable
Motor Control Board	EE-3432-2
MECHANICAL
Back Gauge Nut	43005-1 & 43004-1	S/N: 113558 & Below
	43005-1	S/N: 113559 & Above
Back Gage Floating Fingers	10065	4 per machine
Back Gage Squaring Kit	30010
Clamp Pull Down Rods	10075-1	2 per machine
Cut Stick Stop Repair Kit	K-43058-2	Repair broken screw/stop
Knife Latch	41120-4
Left Side Guide	43058-1	Repair broken cut stick stop
HYDRAULIC
Clamp Cylinder	H-211-3 & (2) H-230-3 Fittings	S/N 169999 & Below
	H-211-3 Only	S/N 170000 & Above
Clamp Press. Valve	H-203-41	Electronic controlled
Clamp Up Seq. Valve	H-203-6
Cut Valve	H-200-2
Elect Clamp Press. Valve Coil	E-1069-()	Reference previously installed coil on machine
Hydraulic Fluid	S-1991-4 (5 gal)      ISO VG 100 Weight	1 gallon tank capacity
Knife Cylinder	K-10018-1	See notes in MAX
	H-210-4	See notes in MAX
Knife Seq. Valve	H-203-17
Oil Replacement Kit	K-43093
Oil Tank Seal	S-1810-37	"O" ring
Press Reducing Valve	H-203-13
Pressure Gauge	8P-629-3	Clear oil filled
230 Standard & TC	CMC-230	Weight 1000 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife Blade � HSS	42007-1
Knife Dimensions	Measures 26-� �x 3� x 3/8�	Minimum Height 2-5/8"
Book Guides	5-7-M361	Each, 2 required
Cutting Stick	42008	(Pkg. of 12) Measures 23� x �� x ��
Cut Stick Hook	5064	For removing the Cut Stick
False Clamp Plate	42013	Mounted with wing nuts
Jogging Aid	A-12608-2	2-7/8" High
Knife Bolts	H-6918-608	5 required
Knife Bolt Washers	8815	5 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	42014
Line/Cut Light Bulbs	E-967-1	12v automotive, #1156
Paper Waste Cart	41058
Magnetic Clamping Pad	50082	2 each 3� x 15�
ELECTRICAL/ ELECTRONIC
Cut Buttons	E-3127-4
Cut Solenoid	E-1069-17	24VAC
Encoder	E-2467
Encoder Coupling	47053	1� long rubber tubing
Knife Latch Assembly	41120-4
LED Line Light Assembly	EE-3081-2	For repairs
Main Board	EE-2807-2	EPROM not included
Preset Board	EE-1688-1
Proximity Switch	E-2204-1	Cut wire to length
Safety Eyes	K-3450	S/N 100189 & Below
	E-3370	S/N 100190 & Above, *For repairs only & E-3336 Controller can be sold separately*
TC Electronics
�CAN� Cable	EE-3460-1	Interface cable between display/motor boards
Display Board	EE-3400-1-C	Board behind LCD panel display
Hand Wheel Potentiometer	EE-3213	With soldered cable
Motor Control Board	EE-3432-2
MECHANICAL
Back Gauge Floating Fingers	10065	8 per machine
Back Gauge Nut	43005-1	S/N 110233 & Above
		S/N 113552 & Below Also order (1) 42019-3 (Leadscrew)
Clamp Pull Down Rods	10075-1
Knife Latch	41120-4
Leadscrew	42019-3
HYDRAULIC
Clamp Cylinder	H-211-3 & (2) H-230-3 Fittings	S/N 169999 & Below
	H-211-3 Only	S/N 170000 & Above
Clamp Press. Valve	H-203-33
Clamp Up Seq. Valve	H-203-6
Cut Valve	H-200-2
Elect clamp Press. Valve	H-203-13
Elect clamp Press. Valve Coil	E-1069-19
Hydraulic Fluid	S-1991-4 (5 gal)      ISO VG 100 Weight	1 gallon tank capacity
Hydraulic Power Unit	H-220-8	240VAC/60Hz
Knife Cylinder	K-10018-1	S/N 110205 & Below
Knife Cylinder	H-210-3	S/N 110206 & Above
Knife Seq. Valve	H-203-17
Manifold O Ring	S-1810-10	3/4� OD
Manifold O Ring	S-1810-15	7/8� OD
Oil Replacement Kit	K-43093
Oil Tank Seal	S-1810-37	"O" ring
Pressure Gauge	8P-629-3	Clear oil filled
265 Standard & TC	CMC-265	Weight 1680 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife Blade � HSS	2263-3
Knife Dimensions	Measures 30-� �x 4� x 3/8�	Minimum Height 3-3/8"
Book Guides	5-7-M361	Each, 2 required
Cutting Stick	4165	(Pkg. of 12) Measures 26-1/2" x �� x ��
Cut Stick Hook	5064	For removing the Cut Stick
False Clamp Plate	44027	Mounts using (3) H-6951-406 set screws
	44027-2	Mounts using (3) H-6951-406 set screws & Also has 44103 False Clamp Pad for Book Trimming
Jogging Aid	A-12608-4	3-5/8� High
Knife Bolts	H-6918-608	6 required
Knife Bolt Washers	8815	6 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	44183
Line/Cut Light Bulbs	E-967-1	12v automotive, #1156
Magnetic clamping pad	50082	2 each 3� x 15�
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC 265 XD, XG, XT, TC
Air Valve/Solenoid Kit	K-47645-1	Replaces solenoid valve black connector style
Cut Solenoid	E-1069-17	24vac
Cut Buttons	E-3073-6	S/N 051553 & Below (Green button switch used in EE-2851-1)
	K-3386	S/N 051554 to 101888 (Kit contains 2 buttons)
	E-3127-4	S/N 101889 & Above (EE-3384 for Right Hand / EE-3385 for Left Hand�Includes both E-3127-4 switch and E-2078 cable for switch)
	K-3367	Ergo Touch Switch Conversion Kit (Non-TC Machines Only)
	K-3424	Ergo Touch Switch Conversion Kit (TC Machines Only)
Electronic Clamp PWM Board	EE-2813	S/N 071754 & Below
Encoder	E-2467
Encoder Coupling	47053	1� long rubber tubing
Encoder Cable	EE-2534-1
Main Board	EE-2807-2	EPROM not included
Preset Board	EE-1688-1
Proximity Switch	E-2204-1	Cut wire to length
Safety eyes	K-3452	S/N 101889 & Below
	E-3370	S/N 101890 & Above, *For repairs only & E-3336 Controller can be sold separately*
1 to 3 Phase Motor Conversion	K-44131	Converts machine to 3 phase
TC Electronics
�CAN� Cable	EE-3460-1	Interface cable between display/motor boards
Display Board	EE-3400-1-C	Board behind LCD panel display
Hand Wheel Potentiometer	EE-3213	With soldered cable
Motor Control Board	EE-3432-2
TC Upgrade of XT & XG	K-3493
MECHANICAL
Air Jet	P-207-2	For Air Table Option
Back Gauge floating fingers	10065	10 per machine
Back Gauge Nut	43005-1	S/N 111917 & Above
		S/N 111916 & Below Also order (1) 44003-1(Lead Screw) as well
Clamp Pull down Rods	44013
Knife Latch	44010-1	S/N 971004 to 981082
	47568-1	S/N 981083 & Above
Leadscrew	44003-1
Left Side Guide	K-44118	Repair broken cut stick stop, Front side guide demensions changed and stop assembly has been added for reinforcement
HYDRAULIC
Clamp Cylinder	H-505
Elect Clamp Pressure Valve	H-203-41
Elect Clamp Pressure Valve Coil	E-1069-19	24VDC
Gasket-Tank	13947
Gasket-Motor	13946
Hydraulic Fluid	S-1991-3 (5 gal)     ISO VG 46 Weight	5 gallon tank capacity
Knife Cylinder	K-44058-1	S/N 971004 to 981082
	K-44058-4	S/N 981083 to 181299
	H-506-5	S/N 181300 & Above & Older machines that have K-44058-4 kit installed already (Identifiable by yellow color cylinder)
Knife Down Sequence Valve	H-203-30	S/N 131965 & Below
	H-203-40	S/N 131966 & Above
Manifold O Ring	S-1810-10	3/4� O.D.
Manifold O Ring	S-1810-15	7/8� O.D.
Oil Filter	H-227-1
Seal Kit	H-504-SK	For H-468-1 Manifold Assembly
Pressure Gauge	8P-629-3	Clear oil filled
CHAMPION Series
305 X,XD,XG,XT,TC	CMC-214	Weight 2500 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife � HSS	47508
Knife Dimensions	Measures 35-�" x 4" x 3/8�	Minimum Height 3"
Backgauge Shield	47002-1	Plastic cover over the back-gauge
Backgauge Tape	K-47279	Eliminates back gage scraping table, 11 ft. of tape
Book Guides	5-7-M361	Each, 2 required
Cutting Sticks	4171	(Pkg of 12) Measures 30 & ��x �� x ��
Cut Stick Puller	5064
Cutter Care Kit	16077 (Contains 16078, 16079, & 16080)	Non-plated table finishing kit
- Table Wax	16078
- Silicone Release	16079
- Rust-B-Gone	16080
False Clamp Plate	47006-2
	47006-5 (With Pad)	For Book Trimming
Jogging Aid	A-12608-4	3-5/8� High
Knife Bolts	H-6918-608	6 required
Knife Bolt Washers	8815	6 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	47575
Line Light Bulb	E-967-1	12v automotive, #1156
Magnetic clamping pad	50082	2 each 3� x 15�
Paper Deflector	AA-13936-1	X Series machines only
Paper Waste Cart	41058
Table Light	S-845	15 watt 18� Fluorescent Lamp
Paper Waste Cart	41058
ELECTRICAL/ ELECTRONIC
1 to 3 Rotary Phase Converter	K-3482	Converts input power to machine from 1 to 3 phase
1 to 3 Phase Motor Conversion	K-3240-2	Converts (208/230 VAC) machine from 1 to 3 phase
Air Valve/Solenoid Kit	K-47645-1	Replaces solenoid valve on "X" Series machines
Auxiliary Starter Contact	E-2376-6	Consult ChallengeTech Support
Cut Buttons	K-3374	S/N 10X1549 & Below, Both buttons included
	E-3127-4	S/N 10X1550 & up (Replaces E-3437-4)
	E-3347	Ergo Touch Switch
	K-3404	Ergo Touch Switch Conversion Kit (For 305 X S/N 10X1549 & Above Only..Nothing exists for S/N's Below)
	K-3404-1	Ergo Touch Switch Conversion Kit (For 305 TC Machines Only)
Line Light Assembly	47538	Uses E-967-1 Bulb
Motor Starter Relay	E-2805-6	Consult ChallengeTech Support
Overload Contactor	E-2441-18	Consult ChallengeTech Support
Proximity Switch	E-2204-1	Rectangular block, cut wire to length
Proximity Switch	E-2204	Round threaded rod, cut wire to length
Safety Eyes	K-3451	S/N 02X299 to 11X1558, Upgrades Older 3 LED Banner Safety Eyes
	E-3370	S/N 11X1559 & Above, *For repairs only & E-3336 Controller can be sold separately*
Table Light Assembly	EE-2149-9	Uses S-845 Bulb
X Encoder	E-2467	Used on manual BG machines as well
X Encoder Cable	EE-2838	S/N 97X104 to 06X1277
X Encoder Cable	EE-2838-3	S/N 06X1278 & Above & Manual BG machines
X Preset Board	EE-2427-S	S/N 07x1358 & Below
X Preset Board	EE-2817-1	S/N 07X1359 & Above & Manual BG machines
X Main Board	EE-2807-2	EPROM not included
XD, XG, XT Encoder	K-3574 (New encoder and cable)
XD, XG, XT Encoder Cable	EE-3030-1 (For use with old encoders)	47178 Cap/Boot cover for Encoder
XD, XG, XT Preset Board	EE-2817-1
XD, XG, XT Main Board	EE-2807-2	EPROM not included
XD, XG Electronic Clamp Board	EE-2813	S/N 07X1360 & Down (PWM Board)
XT Console Repair/Upgrade		Consult Challenge Tech Support
TC electronics
Back-Gauge Control Assembly	49249
Control Knob	63218	Actual knob for the Back-Gauge Control Assembly
�CAN� cable	EE-3460	Interface cable between display/motor boards
Display board	EE-3400-1-C	Board behind LCD panel
Hand wheel potentiometer	EE-3213	With soldered cable
LED Line Light	EE-3489	S/N 151076 & Above
Motor control board	EE-3432-2
Preset proximity	E-2204-6	Must be cut to length
TC Encoder	K-3574 (Contains E-2468-4 Encoder)	S/N 171196 & Below
	E-2468-3	S/N 171197 & Above
TC Encoder Cable	EE-3573 (Used w/ E-2468-4 Encoder)	S/N 171196 & Below
	EE-3564-1 (Used w/ E-2468-3 Encoder)	S/N 171198 & Above
TC upgrade of XT & XG	K-3484	S/N 02X999 to 13X1664
TC upgrade of XT & XG	K-3484-1	S/N 02X998 & Below
HYDRAULIC
Clamp Cylinder	H-431-2
Elec. Clamp Reducer Valve	H-203-41
Filter Head	H-226-1	NPT type fitting (Use H-226-2 for "O" ring type)
Hydraulic Fluid	S-1991-3 (5 gallons)     ISO VG 46 Weight	13.5 gallon tank capacity
Hydraulic Pump	H-387	For 50HZ use H-387-1
Hydraulic. O Ring Kit	H-504-SK	Includes O-rings, Backup Rings, and SAE Plugs.
Knife Cylinder	H-342-1
Knife Down Seq Valve Asm	H-437-1	Just valve is H-203-40
Lower knife cylinder connector	H-434	Knife cylinder to pilot check valve
Oil Filter	H-227-1
O-Ring Top Manifold	S-1810-8	5/8" O.D.
Pressure Gauge	8P-629-3	Clear oil filled
4-Way Valve	K-3000   (AC to DC Valve Conversion Kit)	S/N 02X986 & Below
	H-557	S/N 02X987 & Above
MECHANICAL
Air Jet	P-207-1	S/N 07X1300 & Below
Air Jet	P-207-2	S/N 07X1301 & Above
Back Gauge Floating Fingers	10065	10 per machine, metal
Back Gauge Floating Fingers	60204	10 per machine, plastic
Back Gauge Tape Kit	K-49007	Apply to bottom of back gage
Clamp Cylinder Top Pin	47063	Add (2) H-6451-0500 Clips
Clamp Pull Down Cable	47549-2	S/N 03X1039 & Above
Clamp Pull Down Cable	K-47549-2	S/N 03X1038 & Below
Clamp Return Spring (14� long)	47136-2
Clamp Return Spring (3� long)	47136-1	Located under front cabinet
Knife Adjust Screw	4449	(2) In top of knife bar
Knife Latch	47568-1
Leadscrew Nut	47028	XD, XG, XT, TC
Leadscrew Nut	47029	X, Manual back gage
Left Side Guide	47661	Repair broken cut stick stop
Pin Lock/Keeper	S-1244	Round eyelet, Pin Lock in upper part of machine
	8835	Square plate, Pin keeper in bottom of machine
Pin Assembly - Spring	47090	Upper pin for clamp return spring, has plastic boss, order two H-6451-0500
370 XG, XT, TC	CMC-237	Weight 3700 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knife	49055
Knife Dimensions	Measures 43 1/4" x 4 1/2" x 3/8�	Minimum Height 3"
Backgauge Tape	47269 (sold by the foot - 5 feet required per backgauge)	Eliminates scrapping on table
Book Guides	5-7-M361	Each, 2 required
Cutter Care Kit	16077 (Contains 16078, 16079, & 16080)	Non-plated table finishing kit
- Table Wax	16078
- Silicone Release	16079
- Rust-B-Gone	16080
Cutting Sticks	4173	(Pkg of 12) Measures 37" x �� x ��
Cut Stick Puller	5064
Jogging Aid	A-12608-6	4 5/8� high
Knife Bolts	H-6919-608	9 required
Knife Bolt Washers	8815	9 required
Knife Bolt Wrench	W-164
Knife Lifter Assembly	49226
Magnetic clamping pad	50082	2 each 3� x 15�
ELECTRICAL/ ELECTRONIC
Auxiliary Starter Contact	E-2376-6	Consult Challenge Tech Support
Encoder	E-2468
Encoder Cable	EE-3030
Preset Board	EE-2817
Main Board	EE-2807-2	EPROM Not Included
XD, XG Electronic Clamp Board	EE-2813	S/N 07273 & Below
Line Light Bulb	E-967-1
Cut Buttons	K-3374	S/N 10314 & Below
	E-3127-4	S/N 10315 & Above
Motor Starter Relay	E-2805-7	Consult ChallengeTech Support
Overload Contactor	E-2441-19	Consult ChallengeTech Support
Proximity Switch	E-2204-1	Rectangular block, cut wire to length
Proximity Switch	E-2204	Round threaded rod, cut wire to length
Safety eyes	K-3451	S/N 03230 to 11315, Upgrades original Banner, No upgrade for S/N below 03230
	E-3370	S/N 11316 & Above, *For repairs only & E-3336 Controller can be sold separately*
XT Flash Card & XT Upgrade Kit		Consult Challenge Tech Support
TC electronics
�CAN� cable	EE-3460	Interface cable between display/motor boards
Display board	EE-3400	Board behind LCD panel
Hand wheel potentiometer	EE-3213	With soldered cable
Motor control board	EE-3432
Preset proximity	E-2204-6	Must be cut to length
TC upgrade of XT & XG	K-3491	S/N 03230 & Above
TC upgrade of XT & XG	K-3491-1	S/N 98101 to 03229
HYDRAULIC
Clamp Counter Balance Kit	K-49215
Clamp Cylinder	H-499
Clamp Cylinder Damper	49109
Damper Assembly	49109
Knife Cylinder	H-500-1
Knife Flow Kit	K-49194
Hydraulic Fluid	S-1991-3 (5 gal)	15 gallons, 46 weight
Oil Filter	H-227-1
Pressure Gauge	8P-629-3	Clear oil filled
MECHANICAL
Air Jet	P-207-1	S/N 07265 & Below
Air Jet	P-207-2	S/N 07266 & Above
Back gage Nut	49041
Back gage floating fingers	10065 (12 per machine, metal)	S/N 150999 & Below
Back gage floating fingers	60204 (12 per machine, plastic)	S/N 151000 & Above
Chain Cable Carrier	49200	Approx. 44 7/8� in length.
Knife Adj. Screw	49145
Knife Latch	49228-1
Pin Locks	49217	Newer machine collar design for pin locking in upper part of machine
	8835	Square plate, Pin keeper in bottom of machine & upper part for older machines
DAEHO		Click here to return to the Table of Contents (Page 1)
MANUALS		Consult Challenge Tech Support
CONSUMABLES
Knife Dimensions
Knifes
34�/ 860mm	DA-10000-860, 43 5/16� x 5 ��
40�/ 1016mm	DA-10000-1016, 51 3/16� x 5 ��
45�/ 1160mm	DA-10000-1160, 56 5/8� x 5 ��, s/n 32361 & Below
45�/ 1160mm	DA-10000-1-1160, 54 �� x 6 5/16�, s/n 32362 & Above
52�/ 1320mm	DA-10000-1320, 63 7/8� x 5 ��
54�/ 1370mm	DA-10000-1370, 63 3/16� x 6 5/16�
61�/ 1550mm	DA-10000-1550, 70 7/8�� x 6 5/16�, s/n 52359 & Below
61�/ 1550mm	DA-10000-1-1550, 74� x 6 5/16�, s/n 52360 & Above
Cut Sticks  (Sold Individually)
34�/ 860mm	DA-10001-860
40�/ 1016mm	DA-10001-1016
45�/ 1160mm	DA-10001-1160
52�/ 1320mm	DA-10001-1320
54�/ 1370mm	DA-10001-1370
61�/ 1550mm	DA-10001-1550
DAEHO Accessories
Book Guides	5-7-M361
Fluorescent Table Light Bulb	DA-6100121
Hydraulic Fluid	S-1991-3 (5 gal)	46 weight
Jogging Aid	A-12608-8	40� / 1016mm & less
Jogging Aid	A-12608-20	45� / 1160mm & more
Line Light Halogen Bulbs	DA-6100036	2 per machine, 12v @ 30w
Magnetic Pads	50082	(Pkg of 2) 3� x 15�
20mm Knife Spacer Pin	DA-1200400
30mm Knife Spacer Pin	DA-1200605	Only used on 1160 with polar style knife
Waste Wagon	41058
CMT-130	CMC-130	Weight 1500 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knives (Tungsten carbide)	59051-1	Optional
Knives (Super high speed)	59051-2	Sent standard for all new machines
Knife Dimensions	17.5� x 2.75�	Minimum height 2.50�
Knife Bolt	H-6910-606	7 per knife
Knife Bolt Wrench	W-180
Cut Stick	59050
Cut Stick Puller	5064
Knife Lifter	59070
Reflective Tape � 1� wide	56180	Sold by the foot
Lamp	E-967-1	3 per machine
Jogger Plate UHMW Tape	56523-1000	2
Grease (black)	SU-30-103	Bearing tubes only
Grease (red)	SU-30-104
Clamp Pad	59032
Gripper Pad	59153-1
Waste Bin	41058
ELECTRICAL
Main PCB	EE-2939-2	Without EPROM
Display	EE-3439	White background
Encoder � Registration/Gripper	E-2467-1
Fan	E-2483
PNEUMATICS
Air Filter	56041	Included in K-56040
�� O.D. Nylon Tubing	P-303	Order per/ft. solid white or transparent blue
�� O.D. Flex Tubing)	P-303-1	Order per/ft. transparent yellow/ blue
3/8� O.D. Nylon Tubing	P-303-2	Order per/ft. solid white or transparent blue
3/8� O.D. Flex Tubing	P-303-4	Order per/ft. transparent yellow/ blue
HYDRAULIC
Oil Change Tool Kit	K-56031	Contains tools necessary to change oil
Oil & Filter Kit	K-56040	Contains oil and filter for the CMT's
Hydraulic Fluid	S-1991-3	Included in K-56040, 46 weight
Hydraulic Filter	H-227-1	Included in K-56040
MECHANICAL
Timing Belt � Gripper (white)	59036	78 �� long
Knife Bar Shim � 0.020�	59198
Knife Bar Shim � 0.005�	59199
CMT-130 Accessories
Air Compressor Kit	K-59312
Spare Parts Kit	K-56030-3	CMT130 TC Models
CMT-330	CMC-330	Weight 2540 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Knives (High Speed)	CMT TC - 56248    / Non TC- 56246	3 in a set
Knives (Tungsten carbide)	CMT TC - 56248-1 / Non TC- 56246-1	3 in a set
Knives (Super high speed)	CMT TC - 56248-2 / Non TC- 56246-2	3 in a set
Knife Dimensions	14.5� x 2.75�	Minimum height 2.60�
Knife Bolt	H-6910-605	6 per knife
Knife Bolt Wrench	W-180
Cut Stick	56303
Cut Plate (A series)	56304	2 per machine
Cut Plate (B & C series)	56305	2 per machine
Cut Plate TC Machines	56317	2 per machine
Cut Stick Puller	5064
Knife Lifter	56028	56026 for lifter handle only
Reflective tape � 1� wide	56180	Sold by the foot
Lamp	E-967-1	6 per machine
Table Tape	56527-4700	2
Jog Tape	56523-1000	2
Grease (black)	SU-30-103	Bearing tubes only
Grease (red)	SU-30-104
Face Clamp Pad	56228
Left Clamp Pad	56181
Right Clamp Pad	56181-1
Center Pad	56178
Waste Bin	56143	3 per machine
PNEUMATICS
Air Filter	56041	Included in K-56040
�� OD Nylon Tubing	P-303	Order per/ft. solid white or transparent blue
�� OD Flex Tubing)	P-303-1	Order per/ft. transparent yellow/ blue
3/8� OD Nylon Tubing	P-303-2	Order per/ft. solid white or transparent blue
3/8�� OD Flex Tubing	P-303-4	Order per/ft. transparent yellow/ blue
ELECTRICAL
Main PCB	EE-2939-2	No EPROM
Display Assembly	EE-2758-1	Green back ground display
Display Assembly	EE-3439	White background display
Encoder	E-2467-1
Fan	E-2483
HYDRAULIC
Oil & Filter Kit	K-56040	Contains oil and filter for the CMT's
Oil Change Tool Kit	K-56031	Contains tools necessary to change oil
Hydraulic Fluid	S-1991-3	Included in K-56040, 46 weight
Hydraulic Filter	H-227-1	Included in K-56040
MECHANICAL
Knife Bar Shim � 0.005�	56199
CMT-330 Accessories
	K-56030	Repair Parts-Xerox Support  CMT-330A
Spare Parts Kit	K-56030-1	Repair Parts-Xerox Support  CMT-330B
	K-56030-2	Repair Parts-Xerox Support  CMT-330C
	K-56030-3	Repair Parts-Xerox Support  CMT-330TC
Linear Rail Upgrade	K-56345-3	Send TSB-330TC.012 Kit Instructions with this kit
SCM	CMC-431	Weight 190 / 145 lbs.
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES
Size	Knife	Die
1/8"	6721-2	6722-2     Radius like a credit card
1/4"	6721-4	6722-4     Radius like a dime
3/8"	6721-6	6722-6     Radius like a quarter
1/2"	6721-8	6722-8     Radius like a half dollar
5/8"	6721-10	6722-10   Radius like a silver dollar
Straight Diagonal (45 degree)	6761	6762
Knife/Die Wrench	W-164-2	5/16 hex wrench
Challenge Sharping Service	Return knives must be inspected by Challenge to ensure knives are over 3 5/8� long & that dies are not cracked
ELECTRICAL
Bulb � 25 watt	E-1278	Qty 2 per machine s/n: 2166 and down
Bulb � 75 watt Clear	E-933-2	Qty 1 per machine s/n: 2159A, 2160A, 2167A and up
MECHANICAL
Knife Change Block	8315	Wood block
Pressure Foot Spring � outer	83020	Added to inner spring for more pressure.
Pressure Foot Spring � inner	6727
Foot � Pressure	6724-1	Diameter = 7/8�
Foot � Pressure	6724-2	Diameter = 1 ��
HYDRAULIC
S/n 2167 and up & 2159, 2160
Down valve	H-200-5
Down valve coil	E-1069-13
Hydraulic Fluid - ISO VG 100	S-1991-5 (1 gal)	1 1/2 qt. capacity
Table sensor	EE-3295-2
Accessories
Jogger/Paper Handling Aid	83014
HANDY-DRILL	CMC-322	weight 70 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Drill Drift	4681	Remove drill bit from spindle
Lube Stick	4688	For lubricating drill bits
1/8 Hex Wrench	W-190
9/16 x 1/2 Wrench	W-170
3/16 Hex Wrench	W-130
3/32 Hex Wrench-Short	W-192
Wood Drill Blocks	A-4682	Pkg. of 12   1 �� diameter
ELECTRICAL
Main Power Switch	E-1140-11	Rocker switch
Fuse Holder	E-530-13
Fuse � 3A Slow Blow	E-889-4
Micro Switch	E-866-4	Used for RH & LH chip cup and up limit switch
Spindle Motor	64050
Power Cord � 115VAC	EE-3159
MECHANICAL
Spindle	64052	Order qty. 2 of H-6940-404 �-20 x � flat soc set screw
Pressure Foot	64017
Spring � Pressure Foot	64018	2 per machine
E-Ring	S-1193-37	2 per machine, hold pressure foot in place
Return Spring	6385	13/16� x 6�
HANDY-DRILL Accessories
Side Guide Stops	S-1611-1R
JF Drill (Only uses 2" Drill Bits )	CMC-331	Weights 160 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Wood Drilling Block	A-4682	12 ea. per pkg, 1 �� diameter
Drift Hole Cover	K-85
Drill Drift	4687	Remove drill bit from spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688
ELECTRICAL
Light Bulb	E-933-4
Light Bulb	E-933-2
Spindle Motor	E-1600-21
MECHANICAL
Side Guide Stop	S-1611-1R	Comes with screw
Pressure Foot only	A-4626	Requires 2, S-1518-37
Side Guide Face	A-4791
Safety Shield	A-6891	Plastic guard front of bit
JF Drill Accessories
Cornermatic Corner Attachment	A-4980                      (Only compatible with the JF model drill)	1"/25.4 mm capacity, Includes holder and three blocks, (Knives must be purchased separately)
Fiber Cutting Blocks	KK-474	12 ea. per pkg, 1 �� diameter             (Only for use with cornering knives)
Cornermatic Knives
1/8"/3.2mm	4981-2	Radius like a credit card
1/4"/6.3mm	4981-4	Radius like a dime
3/8"/9.5mm	4981-6	Radius like a quarter
7/16"/11 mm	4981-7	Radius between a quarter and half dollar
1/2"/13 mm	4981-8	Radius like a half dollar
Straight Diagonal	4982
EH-3C	CMC-391	Weight 520 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Drill Blocks	KK-473-3	3" diameter
Spindle Belt	S-1661-1	Flat belt
Drill Drift	4687
Drift Hole Cover	K-85
Drill Drift	4687	Removes drills from the spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688	Pkg. of 12
Gib Lube	6629	Quart
Drill Head Grease	6614	14 oz.
Waste Bin	5739
ELECTRICAL
Foot Switch Assembly	EE-2353-1
Lamp	E-933-4
Start Button	E-3073	N.O. (Green)
Stop Button	E-3073-5	N.C. (Red)
Starter and Heaters	K-3494	S/N 082278 & below
MECHANICAL
Safety Shield	48004
Pressure Foot Assembly	A-4626-7
Pressure Foot Assembly Spring	A-4629-1
Spindle	K-16-4
Spindle Bearing	S-706	2 required per spindle
Front Drill Scale	5859
Index Stop	R-4654
Side head adjuster	5710 knob, 5711 screw, H-6424-8 nut
Left side head block for adjuster	5716-2
Right side head block for adjuster	5716-2
Rubber Insert (only)	5087	S/N 66781 & down
Drill head return springs	K-250-8	2 per machine
Table	5734
HYDRAULIC
Down valve	H-200-5
Down coil	E-1069-17
Hydraulic Fluid	S-1991-4 (5 gal)	1 1/2 qt. capacity
EH-3 Accessories
Automatic Trip Side Guides	A-4615-9	Multiple holes drilling pattern - 7 stops included
Right Hand Side Guide	K-5731
Drill Shield Kit	48004	For S/N 135901 & below
Two Hand Push Button Control
S/N 73123 to 975458	A-4851-45
S/N 975459 to 995773	A-4851-50
S/N 995774 & Above	A-4851-52
EH-3D	CMC-391	Weight 520 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Drill Blocks	KK-473-3	3" diameter
Spindle Belt	S-1661-1	Flat belt
Drill Drift	4687
Drift Hole Cover	K-85
Drill Drift	4687	Removes drills from the spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688	Pkg. of 12
Gib Lube	6629	Quart
Drill Head Grease	6614	14 oz.
Waste Bin	5739
ELECTRICAL
Foot Switch Assembly	EE-2353-1
On/Off Switch	E-3255	S/N 085279 to 105487
Start Button N.O. (Green)	E-3073	S/N 105488 & above
Stop Button N.C. (Red)	E-3073-5	S/N 105488 & above
MECHANICAL
Safety Shield	48004
Pressure Foot Assembly	A-4626-7
Pressure Foot Assembly Spring	A-4629-1
Spindle	K-16-4
Spindle Bearing	S-706	2 required per spindle
Front Drill Scale	5859
Index Stop	R-4654
Side head adjuster	5710 knob, 5711 screw, H-6424-8 nut
Left side head block for adjuster	5716-2
Right side head block for adjuster	5716-2
Rubber Insert (only)	5087	S/N 66781 & below
Drill head return springs	K-250-8	2 per machine
Table	5734
HYDRAULIC
Down valve	H-200-5
Down coil	E-1069-17
Hydraulic Fluid	S-1991-4 (5 gal)	1 1/2 qt. capacity
EH-3 Accessories
Automatic Trip Side Guides	A-4615-9	Multiple holes drilling pattern - 7 stops included
Right Hand Side Guide	K-5731
Drill Shield Kit	48004	For S/N 135901 & below
Two Hand Push Button Control
S/N 73123 to 975458	A-4851-45
S/N 975459 to 995773	A-4851-50
S/N 995774 & Above	A-4851-52
MS-5	CMC-401	Weight 830 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Drill Blocks	A-6626-24	24 per pkg
Drill Head Belt	45160	Flat belt S/N 75237 & above - 63 �"
Drill Head Belt	45034	Flat belt S/N 75236 & below - 65"
Drill Drift Hole Cover	K-85
Drill Drift	4687	Removes drills from the spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688	Pkg. of 12
Gib Lube	6629	Quart
Drill Head Grease	6614	14 oz.
ELECTRICAL
Start Button N.O. (Green)	E-3073
Stop Button N.C. (Red)	E-3073-5
Down Coil	E-1069-13	S/N 965599 & below, 120vac
Down Coil	E-1069-17	S/N 965600 & above, 24vac
MECHANICAL
Drill Head (Standard)	45152	Standard, 1 7/8� on center and head width
Drill Head (Narrow)	45200	Narrow, 1 3/8" on center and head width
Drive Belt	45160	S/N 75237 & Above, 63 1/4� x 1 ��
Drive Belt	45034	S/N 75236 & Below, 65� x 1 ��
Height Adjuster Chain	45135	22.5" S/N 75236 & Below
Height Adjuster Chain	45135-1	24.9" S/N 75237 & Above
Adjuster Sprocket	45139	S/N 75236 & Below 1 �" dia
Adjuster Sprocket	45139-1	S/N 75237 & Above 3 �" dia or if updated w/45164
Cylinder Sprocket	45138	Installs with 2 screws
Drill Head Adjuster Screw	45157	Standard or Narrow   (Adjusts each drill head height)
HYDRAULIC
Down Valve	H-200-5
Hyd. Unit (230/ 1ph /50hz/60hz)	H-450-3	S/N 73614 � 965590
Hyd. Unit (230/ 3ph /50hz/60hz)	H-405-2	S/N 73614 � 965590, order coil E-1069-13
Hyd. Unit (230/ 1ph /50hz/60hz)	H-372-5	S/N 965600 & Above
Hyd. Unit (230/ 3ph /50hz/60hz)	H-405-2	S/N 965600 & Above
Hydraulic Fluid	S-1991-4 (5 gal)	1 1/2 qt. capacity
MS-5 Accessories
Power Cable Kit	K-2889	12' of #10 gauge wire 3 conductor cable
Drill Shield Kit	K-45180	For S/N 135928 and below/standard with new
Two Hand Push Button Control
S/N 74614 to 965599	A-4851-47
S/N 965600 and up	A-4851-48
MS-10A	CMC-411	Weight 1350 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Wood Drill Blocks	A-6626-24	Pkg. of 24, 1 1/4 x 6 x 3/8"
Fiber Cutting Blocks	A-12607	(Only for use with cornering knives)
Plastic Drill Blocks	6669	For large hole drilling only
Standard Drill Heads	A-6594-6
Drift Hole Cover	K-85
Table Light	S-845
Light Ballast	S-1429
Drill Drift	4687	Removes drills from the spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688	Pkg. of 12
Gib Lube	6629	Quart
Drill Head Grease	6614	14 oz.
ELECTRICAL
Push Button	E-1045-6	Red
Push Button	E-1045-5	White
Push Button	E-1045-4	Green
MECHANICAL
Return Spring	6513-2	2 per machine
Latch Spring	16523	Replaces K-300-4
Spindle Belt	S-1716
Taper Pin #5 x 1 ��	H-6633-510
HYDRAULIC
Motor Coupling insert	5087
Cylinder Assembly	H-340	If using in place of A-8400 for older MS-10, see notes in MAX
Hydraulic Fluid	S-1991-4 (5 gal)	1 1/2 qt. capacity
MS-10 Standard Drill Head parts below
Shim	A-6600-4
Spindle Gear	S-1721
Helical Gear	S-1722
Spindle	6596-3
Upper Bushing	S-1720
Lower Bushing	S-1719
Thrust Bearing	S-1723
Plunger	6609	Teflon
MS-10 Accessories
See Under MS-10B
MS-10B	CMC-411	Weight 1350 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
CONSUMABLES	For Drill Bits See Pg. 23
Wood Drill Blocks	A-6626-24	Pkg. of 24, 1 1/4 x 6 x 3/8"
Plastic Drill Blocks	6669	For large hole drilling only
Standard Drill Heads	A-6594-6
Drift Hole Cover	K-85
Table Light	S-845
Light Ballast	S-1429
Drill Drift	4687	Removes drills from the spindle
"T" Drill Drift	A-6588	"T" handle version of 4687
Lube Stick	4688	Pkg. of 12
Gib Lube	6629	Quart
Drill Head Grease	6614	14 oz.
ELECTRICAL
Push Button	E-3129-2	Red
Push Button	E-3129-3	Blue
Push Button	E-3129	Green
Foot Switch Assembly	EE-3246
Fuse	E-1075-1SB
MECHANICAL
Belt	S-1716
Return Spring	6513-2	2 per machine
HYDRAULIC
Down valve	H-200-5
Down coil	E-1069-17
Hydraulic Unit Assembly	H-566
Hydraulic Fluid	S-1991-4 (5 gal)	1 1/2 qt. capacity
MS-10 Standard Drill Head parts
Shim	A-6600-4
Spindle Gear	S-1721
Helical Gear	S-1722
Spindle	6596-3
Upper Bushing	S-1720
Lower Bushing	S-1719
Thrust Bearing	S-1723
Plunger	6609	Teflon
MS-10 Accessories
Fixed Gauges	6653-4	24 Stops (1/4") Spacing
	6653-3	16 Stops (3/8") Spacing
	6653-2	12 Stops (1/2") Spacing
Fixed Side Guide	A-6565
Extra Side Guide Stops	S-1611-1R	For automatic trip side guide
Chip Chute Extension	A-6676	Empties chips out of rear of machine
Triple Drilling Head	A3-6594-5	Drills 3 holes at once, Max = 2 Heads
Large Hole Conversion Package	A-6500-7                  (Only compatible with the MS-10 model drill)	Maximum = 2 Heads
Large Hole Drill Head	A-6594-7
Two Hand Push Button Controls	A-4851-46
Cornermatic Corner Attachment	AA-4980-3               (Only compatible with the MS-10 model drill)	1"/25.4 mm capacity, (Knives must be purchased separately)
Fiber Cutting Blocks	A-12607	(Only for use with cornering knives)
Cornermatic Knives
1/8"/3.2mm	4981-2	Radius like a credit card
1/4"/6.3mm	4981-4	Radius like a dime
3/8"/9.5mm	4981-6	Radius like a quarter
7/16"/11 mm	4981-7	Radius between a quarter and half dollar
1/2"/13 mm	4981-8	Radius like a half dollar
Straight Diagonal	4982
DRILL SHARPENERS & ACCESSORIES		Click here to return to the Table of Contents (Page 1)
Drift	4687	Drill bit removal tool
Drill Bit Adapter	57114	Adapter for LAWSON/NYGREN-DAHLY Drill Bits
Hand	A-4950-2	Sharpening bit 4952, Dowel pin H-5246-216, Rubber washer 5312
Handy Sharp	57100	Sharpening bit 6469, Honing Stone 57108
DRILL BITS		Click here to return to the Table of Contents (Page 1)
Teflon Coated Drill Bits
For Teflon coated bits add "T" at the beginning of the drill bit part # (For example TCD-4 is a Teflon coated, 2" drill bit with 1/4" hole diameter)
2" DRILL BIT	2� Stock drilling capacity unless otherwise stated (overall 3 3/16", shank 2 1/4")
1/8"	CD-2-3	1/2" Drilling Capacity
5/32"	CD-52	1" Drilling Capacity
3/16"	CD-3	1 5/8" Drilling Capacity
7/32"	CD-72	1 5/8" Drilling Capacity
1/4"	CD-4
17/64"	CD-174
9/32"	CD-92
5/16"	CD-5
11/32"	CD-112
3/8"	CD-6
13/32"	CD-132
7/16"	CD-7
1/2"	CD-8
2 1/2" DRILL BIT *Not for JF Drills*	2 1/2" Drilling capacity (overall 3 11/16", shank 2 3/4") *JF Drills cannot use 2 1/2", Only 2" Drill Bits*
1/4"	CD-4-2-1/2
5/16"	CD-5-2-1/2
3/8"	CD-6-2-1/2
7/16"	CD-7-2-1/2
1/2"	CD-8-2-1/2
LARGE HOLE DRILL BITS	Only for use with MS-10 large hole conversion package
9/16"	KDG-9
5/8"	KDG-10
3/4"	KDG-12
1"	KDG-16
1 & 1/8"	KDGB-2
1 & 7/32	KDGB-1.218
1 & 1/4"	KDGB-4
1 & 3/8"	KDGB-6
1 & 1/2"	KDGB-8
HANDY JOG	CMC-461	Weight 15 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
On/Off Switch	E-1140-11
Spring	57012	4 per machine
Coil/Magnet	E-3052
Tray Assemblies
Standard 8 1/2" x 11" (A4)	CMC-461A
Check   (3 Check Bins)	CMC-461A-CK
Large Tray 11" x 17" (A3)	CMC-461A-LG
Jogger Accessories
On/Off Footswitch	E-875-6
COMBO JOGGER	CMC-511	Weight 160 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Casters	S-1755	4 per stand
On/Off Switch	E-963
Table Isolators	S-1759	4 per machine
Foot Pedal Switch	E-875-1
Drive Belt	S-1766
Power cord	E-715-3	12 ft. long
Table Assemblies
Table Assy 20x26 Inches	2026A-6802-1
Table Assy 24x36 Inches	2436A-6802-1
Table Assy 28x40 Inches	2840A-6802-1
Jogger Accessories
Adjustable Wheel Stand	A-6822-1	Stand that adjusts table height from 31" to 40"
I-JOG	CMC-495(No Air) & CMC-497(Air)	Weight 75 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Rocker switches	E-1140-17	Power and blower
Jogger motor	E-1600-201	120v
Table isolators	40016-8	4 per machine
Power cord	EE-3191	120v
Foot pedal	EE-3192
Vacuum motor	66007
Vac motor board	EE-3179
Jogger Accessories
Adjustable Wheel Stand	A-6822-1	Stand that adjusts table height from 31" to 40"
HANDY-PADDER	CMC593	Weight 41 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Clamp � Pipe	S-1882	2 per machine
Clamp Bar	65010	1 per machine
Rubber Foot	A-11074	4 per machine
Door	65009	1 per machine
Turntable	65002	1 per machine
PADDY WAGON	CMC-591	Weight 100 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Clamp	S-1882	2 per machine, Orange slides on pipe, complete
Caster � 3�	S-1881	4 per machine
Caster � 5�	S-1881-1	4 per machine
Door	7401	2 per machine
Clamp Bar	7411
Door Handle	S-1883
HANDY-CART	CMC-613	Weight 72 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Caster � 5�	S-1881-1	4 per cart
7/16 Nut	H-6414-7	4 per cart
PAK-RAK II	CMC-612	Weight 170 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Caster	S-1881	4 per machine
R H Tray	7489
L H Tray	7490
820/870-MEDALIST		Weight 275 lbs
Click here for available manuals at challengemachinery.com		Click here to return to the Table of Contents (Page 1)
Basic �Combo� Roller Rebuild Kit K-35294
Combo Rollers	35055               Metal / Rubber	4
Roller Gears	35052               Spur, helical N/A	4
Gear Keys	H-6121-604      Wood drift key	4
Idle Roller Bushings	A-10257-5	6
Main Roller Bushings	35029	2
Sucker Wheel Belt	35113	2
�O� Ring Drive Belt	35179-1	5
Out feed Tires	A-10249	4
Tech Notes	MFG 016	1
Basic �Rubber� Roller Rebuild Kit K-35293
Rubber Rollers	35051	4
Roller Gears	35052                Spur, helical N/A	4
Gear Keys	H-6121-604       Wood drift key	4
Idle Rollers Bushings	A-10257-5	6
Main Roller Bushings	35029	2
Sucker Wheel Belt	35113	2
�O� Ring Drive Belt	35179-1	5
Out feed Tires	A-10249	4
Tech Notes	MFG 016	1
Basic �820� Roller Rebuild Kit K-35298
Rubber Rollers	35051	4
Roller Gears	35052                Spur, helical N/A	4
Gear Keys	H-6121-604       Wood drift key	4
Idle Rollers Bushings	35283	6
Main Roller Bushings	35029	2
Roller Spring	7922	6
Sucker Wheel Belt	35113	2
�O� Ring Drive Belt	35179-1	5
Out Feed Tires	A-10249	4
Tech Notes	MFG 016	1
Delivery/Stacker
Folding Chart	A-11091	1
Drive Gear	35223-1            Steel, used to be plastic	1
Drive Belts	36094               Timing Belt	2
Delivery Belts	35138               Short Delivery	2
Delivery Belts	35138-1            Long Delivery	2
Air Feed Table
Paper Backstop	AA-11251-1	1
Bearings	35258	2
Sucker Wheel Shaft	35257	1
Separator Plate	35120	1
Side Guide Bottom Plate	35097-2	1
Side Guide Bottom Plate	35097-3	1
Bottom Plate Strip	35277-1	1
Paper Hold Down	Order six items below for 1 paper hold down
Separator clamp	35084	1
Paper guide	35083	1
Paper guide clamp	35082	1
Knob	8278-1	1
#10 washer	H-7321-#10	1
Button head screw	H-6920-103203	2
Drive Belts
Motor to Hand Wheel	A-11273	1
Hand Wheel to Main	7954-1	1
Electrical
Power On/Off Switch	E-1140-11	1
Fuse (motor/display)	E-889-6         5A slo-blo	1
Fuse (vac pump)	E-889-31       15A slo-blo	1
Speed On/Off Switch	K-2654          Replaces red/green switch	1
Speed Control PCB (120V)	E-1651          Amp sensing resistor E-2126-3	1
Motor	E-1600-148   120vac only	1
Motor Brushes	E-812-5         Leeson, Mototronics	2
Motor Brushes	E-812-6         Baldor	2
Motor Brushes	E-812-7         Magnetek / Ind. Gen.	2
Vacuum Pump Filters	P-282	2
Vac pump switch	E-1140-11	1
Vac Pump Power Cord	E-2343	1
Vac Pump Cord Socket	E-2332          Power panel socket	1